+

Please confirm you are not a robot

Shower & Wall Peel & Stick Caulk - White

Write Review
Write Your Own Review
You're reviewing:Shower & Wall Peel & Stick Caulk - White
Rating
Write Review
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account

Recaulking your shower and wall doesn't have to be a pain with Magic Shower & Wall Peel & Stick Caulk. It's designed to provide a flush seal without the usual mess of caulking. Color: White

$7.25
-
+

Additional Supplies Needed: Caulk removal tool, paint thinner or mineral spirits, scouring powder, scrubbing pad, rubbing (isopropyl) alcohol, paper towel or clean rags, tape measure, scissors

Directions: For proper adhesion, please follow the instructions carefully. Utilize proper protective equipment when completing this project. Review all cautionary information on each manufacturer label for guidance.

Surface Preparation: Preparing the surface is critical to successful adhesion of Magic Peel & Stick Caulk.

  1. Remove all existing caulk. Paint thinner or mineral spirits can be used to soften caulk prior to removal.
  2. Thoroughly clean the surface with scouring powder to remove all residue, and then rinse with water.
  3. Wipe previously caulked areas with rubbing alcohol.
  4. Dry all surfaces thoroughly.

Application:

  1. Measure where you would like to apply the caulk and cut strips of caulk to length. Do not continue the same length of caulk around corners. Cut into separate strips.
  2. Starting in the corner, peel a small section of the backing from the strip. Press strip firmly to shower and wall surface. Work carefully to avoid having to reposition the strip once adhered.
  3. Working in small sections at a time, continue to slowly pull off backing and press the strip firmly until the entire strip is adhered.
  4. Prevent water contact with caulk for a minimum of 12 hours after installation.
How do I use this product around corners?

You will need to cut the caulk into separate pieces and align them at the corner.

Can I use this on top of existing caulk?

No. Prepping the surface is critical to the product working correctly. Part of those prepping instructions (which you can find under the “Directions” section) includes removing all existing caulk from the area for proper adhesion.

Magic Peel & Stick Caulk is an easy alternative to traditional caulk. Designed to create a tight seal between the shower and wall to keep moisture out and create a clean finished look.

Size: 1/2" x 10' (1.3cm x 3.05m)

Color: White

Suministros Adicionales Necesarios: Herramienta para quitar la masilla, diluyente o solvente mineral, polvo limpiador, almohadilla aplicadora, alcohol isopropílico, toallas de papel o trapo limpio, cinta métrica, tijeras.

Instrucciones: Para una correcta adhesión, siga las instrucciones cuidadosamente. Utilice el equipo de protección adecuado para realizar esta tarea. Revise todas las precauciones suministradas por cada fabricante en las etiquetas correspondientes.

Preparción de la Superficie: La preparación de la superficie es un paso crítico para lograr la correcta adhesión de Magic Peel & Stick Caulk.

  1. Remueva completamente la masilla existente. Puede usar diluyente o solvente mineral para ablandar la masilla antes de removerla.
  2. Limpie completamente la superficie con polvo limpiador para eliminar restos de suciedad y residuos, y enjuague con agua.
  3. Limpie con alcohol isopropílico las áreas donde había masilla.
  4. Enjuague las superficies completamente.

Aplicación:

  1. Mida el lugar donde desea aplicar la cinta selladora y corte cintas con las medidas correctas. No use una misma cinta continua a lo largo de las esquinas. Corte cintas por separado.
  2. Comenzando desde la esquina, quite una pequeña sección del papel protector de la cinta. Presione firmemente contra la ducha y la superficie de la pared. Trabaje cuidadosamente para evitar tener que reposicionar la cinta una vez adherida.
  3. Trabaje en pequeñas secciones y continúe quitando el papel protector lentamente y presionando firmemente hasta que toda la cinta selladora quede adherida.
  4. Evite que el agua entre en contacto con la masilla durante 12 horas después a la instalación, como mínimo.
Trusted #1 Brand